Parts & Accessories

Salsa springs for Flip-Off skewers

Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place

End caps for front conversion hubs.

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 15mm - 1 cone per bag Note: O-ring / seal not included. Check the seal groove closely. This cone has a narrower groove than cone CN-R002. COMPATIBLE HUBS: - 105 FH-5700, 9 speed (right side cone) - 105 SC 1051, 7 Speed Rear - RX100 A551, 8 Speed Rear - RSX 410, 7 Speed Rear - Deore LX M550, 7 Speed Rear - Deore Mtn LX M550, 7 Speed Rear

Surly Thru-Axles are low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Offered in several sizes, for both front and rear wheels. 12x142 Rear Thru Axle: - Fits: Midnight Special and MDS Dropout bikes including Instigator, Legacy Karate Monkey & Legacy Krampus. 12x142/148 Rear Thru Axle: - Designed for frames with Surly Gnot Boost spacing (145mm), capable of working with 142 or 148mm rear hubs - Fits: Karate Monkey, Krampus, Troll, Ogre, ECR 12x177 Rear Thru Axle: - Fits: Wednesday 12x197 Rear Thru Axle: - Fits: Ice Cream Truck, Big Fat Dummy 12x100 Front Thru Axle: - Fits: Midnight Special 15x110 Front Thru Axle: - Fits: Karate Monkey, Krampus 15x150 Front Thru Axle: - Fits: Wednesday, Ice Cream Truck, Big Fat Dummy

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

Add an Alfine hub, cog, spokes, and a rim to this Shimano Internally Geared Hub Small Parts Kit, and you're ready to rock. - Alfine hubs are packaged without small parts and require this kit plus a cog - Nexus hubs are packaged with small parts and cogs and do not require an additional small parts kit - For 11-Speed Hub - Includes CJ-S700 Cassette Joint for Vertical Dropouts *Cassette joint does not fit Di2 Alfine hubs

This is a set of replacement internals for Alfine SG-S700 11-Speed internally geared hubs, allowing you to reuse your old Alfine shell with brand new internals, making it like a new hub. - 187mm axle width

When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.

Replacement Freehub Body for Trace hubs.

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Heavy duty and extra wide PVC rim strips for maximum tube protection.

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

High-quality replacement skewer to keep the bike moving. - Skewer for Boost 141 rear wheels - Neutral black lever and steel axle

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.

Parts for RaceFace hubs.

Includes rim strip and tubeless tape for 1 wheel.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

- Designed to stabilize 15g spokes in most hub flanges - 1000-pack

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

Replacement freehub spoke protector, in various sizes for different freehub sizes. - Made of clear plastic - 3 hooks for affixing to spokes

Freehub bodies for Zipp Cognition hubs.